Detailed Engineering 04

Day 1 Introduction of Electrical design
4 Lessons
- Session 2 Electrical Design part cont.
  Start
- Session 1 Introduction to Electrical Design
  Start
- Slides
  Start
- Day 1 Assignments
  Start
DAy 2 Standards
7 Lessons
- List of Standards used for electrical design
  Start
- List of Softwares
  Start
- Stanadrds and softwares
  Start
- Session 1
  Start
- Session 2
  Start
- List of software's slide
  Start
- Day 2 Assignments
  Start
Day 3 MDR Preparation
4 Lessons
- Session 2
  Start
- Session 1
  Start
- Material
  Start
- Day 3 Assignments
  Start
Day 4 Electrical Design Basis and Load List Preparation
4 Lessons
- "Electrical Design philosophy / Basis of design , Input list for Electrical Load list , Classification of loads (Continuous, Intermittent, Standby) , Electrical Load Estimation or Load list preparati
  Start
- Course Material
  Start
- Day 4 Assignments
  Start
- Slides
  Start
Day 5 Electrical Distribution Philosophy
6 Lessons
- Session 2
  Start
- Session 1
  Start
- Slides
  Start
- ABB catlog
  Start
- Day 5 Assignments
  Start
- Book
  Start
Day 6 System Earthing and Transformer / Generator sizing
4 Lessons
- Slides
  Start
- Session 1
  Start
- Course Materials
  Start
- Assignment Day 6
  Start
Day 7 OLTC / DETC and SLD - key SLD Discussion
4 Lessons
- Session 1 OLTC / DETC and SLD - key SLD Discussion
  Start
- Key SLD
  Start
- Excel Notes
  Start
- Day 7 Assignments
  Start
Day 8 Metering and protection SLD
3 Lessons
- Session 1 Metering and protection SLD
  Start
- Materials
  Start
- Slides
  Start
Day 9 Short Circuit Calculation
3 Lessons
- Session 1
  Start
- Session 2
  Start
- Slides
  Start
Day 10 Short Circuit Calculation (Manual Calculation)
3 Lessons
- Session 1
  Start
- Book
  Start
- Excel Calculation
  Start
Day 11: Course Benefits and Review of Day 1 & 2
1 Lesson
- Course Benefits & Review of Day 1 & Day 2
  Start
Day 12: Review of Day 3 to Day 10
4 Lessons
- Review of Day 3 to Day 10
  Start
- K R Monograph
  Start
- Transmission Line - Standard Conductor Parameters
  Start
- Notes
  Start
Day 13 Switchgears Selection
2 Lessons
- Session 1
  Start
- Slides
  Start
Day 14 Cable Selection and Sizing
3 Lessons
- Day 14 Cable Selection and sizing
  Start
- Slides
  Start
- cable sizing notes
  Start
Day 15 Specification preparation and cable schedule
3 Lessons
- Specification preparation and Cable Schedule
  Start
- notes
  Start
- slides
  Start
Day 16 Cable sizing
1 Lesson
- Cable Sizing
  Start
Day 17 Motor starter schematics
1 Lesson
- Types of Starters - DOL, Star delta, Soft starter, VSDS and What is Type 2 coordination?
  Start
Day 18: "Introduction to Brown Field Project and SLD, Brown Field Project Challnges"
1 Lesson
- "Introduction to Brown Field Project and SLD, Brown Field Project Challnges"
  Start
Day 18: KR_Monograph_Jan_2022_R5
1 Lesson
- KR_Monograph_Jan_2022_R5
  Start
Day 19: Starters and Type 1 ,2 Coordination
2 Lessons
- Starters and Type 1 ,2 Coordination
  Start
- Materials
  Start
Day 20 CT VT Sizing, Instrument Transformers
3 Lessons
- Materials
  Start
- Slides
  Start
- Day 20: Instrument Transformers , CT / VT sizing calculation, Sample calculation
  Start
Day 21 Transformer
4 Lessons
- Slides
  Start
- Areva Book
  Start
- Materials
  Start
- Day 21 : - IEC 60076 - Power and distribution Transformers - Application of Different type of Transformers - OLTC/DETC
  Start
Day 22 Batteries and DC UPS
4 Lessons
- Slides
  Start
- Sample Calculation Sheet
  Start
- DC UPS Mind Map
  Start
- Day 22 : Batteries, IEEE 485/1115 Standards, Application of Batteries, Battery sizing calculation
  Start
Day 23: DC UPS cont.
1 Lesson
- Day 23 : Continuation of Batteries, IEEE 485/1115 Standards, Application of Batteries, Battery sizing calculation
  Start
Day 24: Capacitor banks,Application of Capacitor banks,Capacitor banks sizing calculation,Specification and data sheet preparation Assignments: Capacitor bank sizing calculation for given
1 Lesson
- Day 24: Capacitor banks,Application of Capacitor banks,Capacitor banks sizing calculation,Specification and data sheet preparation Assignments: Capacitor bank sizing calculation for given
  Start
Day 25: Capacitors - Application, Shunt and Series Capacitor
3 Lessons
- Capacitors - Application, Shunt and Series Capacitor
  Start
- Cap Sizing
  Start
- Capacitor
  Start
Day 26 Motors
2 Lessons
- Motors
  Start
- Motor2
  Start
Day 27 Technical Bid Analysis and Vendor Document Review
1 Lesson
- TBA
  Start
Day 28 Design Requirement Substations
2 Lessons
- Slides
  Start
- Substations
  Start
Day 29: Substation Design consideration and Cable tray planning
1 Lesson
- Substation Design consideration and Cable tray planning
  Start
Day 30: Grounding
1 Lesson
- Grounding
  Start
Day 31: Grounding- Case Study
1 Lesson
- Grounding Case Study
  Start
Day 32: Design of Lightning protection system - Risk assessment calculation (As per IEC 62305)
2 Lessons
- External Lightning protection system, Rolling sphere, Protective angle method, Mesh method, Internal Lightning protection system, Lighting protection system layouts
  Start
- Materials
  Start
Day 33: Lighting Design
1 Lesson
- Lighting Design
  Start
Day 34: Lighting
3 Lessons
- Day 34: Lighting
  Start
- Lighting Mindmap
  Start
- Materials
  Start
Day 35: Assignment Review
2 Lessons
- Session 1: Overview of Course and Assignment 1 Review
  Start
- Session 2: Assignment Review
  Start

Detailed Engineering 04

Course Summary

Course Curriculum

Day 1 Introduction of Electrical design

DAy 2 Standards

Day 3 MDR Preparation

Day 4 Electrical Design Basis and Load List Preparation

Day 5 Electrical Distribution Philosophy

Day 6 System Earthing and Transformer / Generator sizing

Day 7 OLTC / DETC and SLD - key SLD Discussion

Day 8 Metering and protection SLD

Day 9 Short Circuit Calculation

Day 10 Short Circuit Calculation (Manual Calculation)

Day 11: Course Benefits and Review of Day 1 & 2

Day 12: Review of Day 3 to Day 10

Day 13 Switchgears Selection

Day 14 Cable Selection and Sizing

Day 15 Specification preparation and cable schedule

Day 16 Cable sizing

Day 17 Motor starter schematics

Day 18: "Introduction to Brown Field Project and SLD, Brown Field Project Challnges"

Day 18: KR_Monograph_Jan_2022_R5

Day 19: Starters and Type 1 ,2 Coordination

Day 20 CT VT Sizing, Instrument Transformers

Day 21 Transformer

Day 22 Batteries and DC UPS

Day 23: DC UPS cont.

Day 24: Capacitor banks,Application of Capacitor banks,Capacitor banks sizing calculation,Specification and data sheet preparation Assignments: Capacitor bank sizing calculation for given

Day 25: Capacitors - Application, Shunt and Series Capacitor

Day 26 Motors

Day 27 Technical Bid Analysis and Vendor Document Review

Day 28 Design Requirement Substations

Day 29: Substation Design consideration and Cable tray planning

Day 30: Grounding

Day 31: Grounding- Case Study

Day 32: Design of Lightning protection system - Risk assessment calculation (As per IEC 62305)

Day 33: Lighting Design

Day 34: Lighting

Day 35: Assignment Review

Jeyakumar Velusamy

Akila

John Smith

Highly Recommended Course. Easy to Understand, Informative, Very Well Organized. The Course is Full of Practical and Valuable for Anyone who wants to Enhance their Skills. Really Enjoyed it. Thank you!!

Course Pricing